Very well maintained and consistently updated Motoryacht. She had V12 Cat Engines (3412’s) and cruises at 20 knots all day or cross oceans at 8 knots like a Trawler. You won’t find a better example of this classic Motoryacht. She is owned by a knowledgeable yachtsman that always keeps her in excellent condition cosmetically and mechanically. This vessel shows like a much newer model due to excellent care since new and steady upgrades over the years.
This Marlow 78E is located in Florida, please contact us at 514-521-1221 for all details about this Marlow.
Click here for direct link to the Marlow web site for this model.
New Garmin electronics with 3 17″ monitors, new depth sounder module, 6′ 12KW Radar, and XM Sat Weather.
New Hunter Douglas Silhouette blinds have been installed in the Salon, Pilothouse/Galley, and Command Bridge. Built in Seating has all been recovered as well. The Salon in Fabric and the Pilothouse in Ultraleather.
Added Alas shore power boost transformers (2 50A)
Upgraded to led interior lights
Added 4 Lumashore underwater lights (White/Blue)
The main Engine Exhaust was redone sometime prior to the owner purchasing the vessel. The exact date is unknown, but it has been redone and is in good condition.
New Air Conditioner Chillers for chilled water system
Beach to Beach could easily pass for a vessel that is much newer than her hull number indicates. Every aspect of this yacht shows well from the new fabrics in the salon to the tidy engine room. This boat is ready to cruise.
Low profile, seaworthy appearance, high bow, flawless exterior craftsmanship, superb joinery and proper equipment selection are always the initial feelings as you board any Marlow Yacht. Passageways are wide and bulwarks high and safe. Beach to Beach provides all that, as well as a very functional layout and warm, spacious interior.
This yacht feels much larger than similar length vessels due to her open floor plan. When you walk in the salon you can see right through the dinning room and galley to the forward windows.
One enters the Salon aft from the Aft Deck and immediately observes a complete sight line to the forward windshield, as well as the large windows along each salon side. You immediately see a properly shaped Salon and a very nice Dining Room forward of the Salon. There are no long and skinny or short, stocky rooms here, just a feeling of comfortable proportions. To starboard is a large settee just redone in high end off white upholstery fabric. The cushions lift up on gas shocks providing lots of storage. The end tables provide additional storage and house the very quiet air handlers which supply the longitudinal air distribution system in the louvered valence. No hot spots or cold spots, just comfortable, quiet air distribution.
To port is the Pop-up television and room to place two luxurious chairs. Forward to port is the wet-bar with Sub-Zero dual temperature wine cooler, extra bottle storage, stainless steel sink, and refrigerator with ice maker. The sink and ice maker are supplied with specially filtered water from the drinking water tank. All light fixtures, and cabinet handles and hardware are gold-plated for beauty and added protection from moisture.
New Hunter Douglas Silhouette blinds have been installed in the Salon, Pilothouse/Galley, and Command Bridge
At the forward end of this level is the custom crafted teak and ebony dining table with six custom factory built chairs that have just had the upholstery redone. Adjacent are the built-in lighted china and crystal cabinets. The Buffet forward has a row of drawers perfect for silverware and miscellaneous serving items.
Up three steps to the U-shaped Galley with black diamond granite counter top, stainless steel Franke sink with cutting board cover, Grohe faucets, sink disposal, Dacor smooth glass-top electric range with removable stainless steel sea rails and pot keepers, Dacor oven, additional microwave, convection oven, Sub-Zero drawer refrigerators and freezers, trash compactor and Fisher-Paykel single-drawer dishwasher. There are abundant cabinets and drawers. Gourmet cooks flourish in this wide open well-equipped galley.
Forward of the galley is a comfortable seating area and very functional office area. if you are still finding yourself on the computer while boating, there is no better place to be than at this desk. This area is great at port or underway. I am writing this listing sitting at this desk and it offers the best views of any waterfront office and it would be a great place to sit while someone is working in the galley. Just to port is another table and seating for 4 adults. Underway this will be a popular spot as you are looking out the front windows.
The full beam master stateroom takes great advantage of the warm and open feeling. The king size bed is on centerline with abundant drawer storage and hanging lockers to port and starboard. Also to port is a vanity. Additional storage is located in drawers beneath the bed. Shoji screens to port and starboard permit light to enter the stateroom while providing privacy in marinas. The substantial stainless steel ports on both sides permit cross-ventilation when open and maintain watertight integrity at sea. Aft on both sides are light and airy his and hers heads with a common shower. Granite counter tops, Grohe fixtures, Vacuflush toilets are but a few of the luxuries in the heads. A full-size Bosch washer and dryer are locate in the forward locker in the Master Stateroom.
VIP GUEST STATEROOM:
The VIP Stateroom will make your family and guests feel extremely welcome. Developed for the owner’s family, this stateroom includes a king-size bed, two large hanging lockers, six large drawers and additional lockers. It is light and airy, due to the opening deck hatches with Oceanaire screen and blackout shades. The en suite oversize head is also light and airy, with granite counter, large Lexan shower stall with curved, teak trimmed Lexan shower door, opening port, Vacuflush toilet, Grohe fixtures and large mirror. A separate door to the companionway allows this head to be used as a day head or to be shared with the adjacent starboard guest stateroom.
PORT GUEST STATEROOM:
This stateroom provides two single berths and an additional Pullman upper berth, hanging locker and drawer storage. The en suite guest head has an opening port, large Lexan shower, granite counter, and Grohe fixtures.
STARBOARD GUEST STATEROOM:
This stateroom is intended for additional overflow sleeping with upper and lower berths, large mirror, opening ports, and curtain enclosure. When not in use, the curtain is left open, providing a more spacious feeling.
The crew quarters are configured with three single berths, head with shower, hanging lockers, drawers and bins, a desk, refrigerator, microwave, TV and FM and CD radio, and a combination washer/dryer . Noting that “a happy crew is a happy ship”, the owner has ensured that all furnishings are the same quality as provided in the guest quarters in Beach to Beach.
The Command Bridge is conveniently located ten steps up from the galley. This enclosed bridge is finished in satin teak with teak and holly decks, Stidd pilot and copilot helm chairs, port and starboard L-settees (raised for full visibility)with elegant teak tables, and a refrigerator with icemaker provide the creature comforts to this fully air conditioned and heated space. Port and starboard watertight sliding doors allow immediate access to the side decks. The hinged aft watertight door permits access to the Boat Deck. Large double layer tempered glass windows (laminated with hurricane film intermediate strengthening to maintain watertight integrity), provide 360 degree visibility. Oceanaire hatches with screens and blackout covers allow ventilation. The Marlow proprietary safety and control panel is located above the windshield. A large L-shaped teak console with 3 monitors and dashboard displays navigation and engine condition information. Windshield wipers and washers afford excellent visibility in the worst conditions. The spotlight remote controls and Kahlenberg trumpet horn controls are located at the helm.
(3) 17″ Garmin Chart plotter Screens
12KW Radar with 6′ Array
Garmin GSD 24 transducer
XM GXM54 Sat Weather
FLIR Night vison
ICOM Vhf Radio
Yacht Controller Wireless control for engines and thrusters
As with all fine Mediterranean yachts and many in the US, one boards Beach to Beach from the stern via Passarelle or either stairway from the wide swim platform, or from either side via boarding gates. The integrated Swim Platform is exceptionally large with protective removable N-rails to assist in boarding from a tender or floating dock. A watertight ship’s door in the transom provides shoreside access to the lazarette and crew quarters. There are twin port and starboard stairs to the Aft Deck twin transom doors. The Aft Deck is spacious, with cockpit bench seat and aft deck table and features 4 beautiful high gloss Teak chairs. Adjacent to the salon bulkhead to port of the Salon door is an entrance to the Crew Quarters and Engine Room. Above this is a beautifully arched stainless steel and teak ladder to the Boat Deck. To starboard are the Aft Deck Docking Station and a sink. Both wide side decks run forward from the Aft Deck. Side boarding gates are provided here. Two wide doors (one hinged and one sliding) create a 5-foot opening to the Salon.
Immediately aft of the Command Bridge is the Boat Deck, with a cabin top overhang forward, U-shaped settee/lounge and table to starboard, and Day Head with Vacuflush toilet and Grohe fixtures to port. Also to port is the Barbecue area with Magma gas grill, refrigerator with icemaker, sink and storage lockers. The ladder to the aft deck and one to reach the top of the Command Bridge are here. A sliding hatch covers the opening to the aft deck stairs. Aft are the fully hydraulic remote controlled 1600-pound dinghy crane and custom stainless steel dinghy chocks that will accept up to a 15-foot dinghy. The stainless steel rails on the boat deck have been extended to the end of the boat deck and five removable N-rails are installed across the end. A remote control station is located here.
2013 Zodiac Yachtline 380DL 12′
Yamaha F40LA 4 stroke motor
9 Gallon Fuel Tank
The Engine Room has standing headroom and has been designed to allow very good access to all equipment. Placing fuel tanks forward of the Engine Room allows the full beam to be used for equipment placement. Attention to detail enables key maintenance access, which leads to proper adherence to maintenance cycles, which yields maximum operational time (rather than being stuck in port for repairs to equipment which had been ignored).
The twin cross-connected sea chests forward provide all the sea water to the Engine Room, a safety factor over boats built with ubiquitous inlets wherever it suits the builder. Commercial and military vessels use sea chests. Two 25 kW Northern Lights generators in custom sound boxes with clear Lexan windows provide redundant electrical power at sea (each generator will independently carry the entire vessel electrical load).
The dual, redundant and supplementary, chilled water compressors and the start/finish of the circulating cold/hot water closed loop are here.
The redundant Naiad stabilizer hydraulics as well as redundant hydraulics for steering are located here. You won’t lose steering or stabilizers if you shut down one engine. On the forward bulkhead is the simplest fuel management system.
Due to tank location (at the vessel center of gravity), no fuel is necessary for trim or ballast, allowing all supply and return valves to remain open unless equipment isolation is desired. Aft are the Centaflex couplings which allow vibration isolation of the engines and the exhaust systems, something done by no other yacht builder, and contributing to the Marlow Yacht reputation for “smooth ride.”
Exceptional sound isolation of this compartment and the additional sound isolation provided by two bulkheads and 3500 gallons of fuel tankage enable normal conversations to take place in the Salon and the Master Stateroom while operating at the 27-knot full speed. Stainless steel engine beds support the engines, absorb the forward thrust from the large thrust bearings of the Centaflex couplings, and transmit it smoothly to the hull. A Sea Recovery watermaker system has been provided.
A separate pump room is located in below the forward berthing compartments. This space contains the fresh water and drinking water filters (to remove particulates, taste and odors) and pumps, redundant water pump and water distribution manifold. The water maker output connects to the separate drinking water and fresh water systems here.
- Twin Caterpillar 3412E 1400 HP engines (2,600 hours)
- Two 25 KW Northern Lights generators in custom Lexan sound shields -2300 Hours each
- 4000 watt Sine wave inverter/ Charger
- Bow and Stern Sidepower, 48V, 20 HP Each with controls at helm, aft deck, and remote stations
- 2 Forward and 2 Aft 50 Amp Shore Power inlets- All with Glendinning Cablemasters
- Backlighted electrical Panels
- Carbon Monoxide detectors in all berthing spaces
- Centaflex flexible drive couplings,
- Soft Motor Mounts
- Two Cross-Connected Sea Chest Sea Water Intakes with cleanouts
- Drypoint Demister air Intake System
- FRP Fuel Tank (3500 gallons) with sump and cleanout
- Fuel Manifold and proprietary Sight Gauge
- Dual Racor fuel filters with pressure gages for each engine and generator
- Fire Suppressant System
- Engine Room Lead/Foam Sound and Heat Insulation System
- Heavy Duty (3700 GPH) bilge pumps and high water alarm
- 4 220V High Volume Engine Room Blowers
- Color coded Piping
- Polished Stainless Steel Engine beds
- Gel coated bilges
- Oil change system
- Engine Room Lighting. 110 Volt and 24 Volt
- Common Drainage System from Bow to Stern collects deck drain, scupper and sump discharges
- Underwater Exhaust
- 50 gallon Hot water supply- 2 SS Tanks
- Gray Water (180 gallon) and black water( 175 gallon) holding tanks with dockside and at sea discharge controls
- Fresh Water 350 gallons
- Drinking Water 114 gallons
On the Command Bridge three 17-inch monitors display radar, navigation, on-board, local and national TV pictures, weather, depth and thermal imaging pictures. Beach to Beach has a recently upgraded Garmin integrated electronics system with the following capabilities
- (3) 17″ Garmin Chart plotter Screens
- 12KW Radar with 6′ Array
- Garmin GSD 24 transducer
- XM GXM54 Sat Weather
- FLIR Night vison
- ICOM Vhf Radio
- Raymarine Autopilot
- Yacht Controller Wireless control for engines and thrusters
- ICOM M604 VHF with hailer/fog functions and additional Command microphone at Office
- Newmar Hailer Horn
- Satellite TV antenna
- FLIR IR camera
- Bose Entertainment system in Salon
Beach to Beach is built using the most modern materials, taking advantage of light weight and extremely strong characteristics to provide fuel saving at any speed, Kevlar in the outer laminate provides resistance to punctures, tremendous strength at sea in bad weather, and the friendly open feeling of a hull without many unnecessary view-interfering bulkheads. The drystack Resin Infusion Vacuum Assisted Transfer (RIVAT) technique saves weight and enhances strength. The Corecell core is engineered for strength, laminating ease and resistance to any water intrusion.
Three major, complex molds are used to build the vessel, minimizing the number of seems and maximizing strength. The primary structure consists of inner and outer laminates highly engineered E-Glass and Kevlar in combination with SAN Corecell foam sandwich, laid up with modified epoxy resins.
The under body is unique, with twin Velocijet strut keels and mild propeller tunnels. The tunnels permit the propellers to be raised and the thrust along the shafts to be more in line with the forward direction of the vessel. The tunnels improve water flow into the propellers, enhancing thrust. The Velocijet strut keels house and completely protect the shafts and extend below and protect the propellers. They are strong enough to support the boat when out of the water in a boatyard, or during an unfortunate grounding. The Kevlar skin protects against impact with logs, deadheads and minor and major debris.
The hull is finished with Oyster White Awlgrip Paint. All false planking lines are crisp and the hull shines. The deck drains and scuppers lead to the continuous drainage system, which runs from bow to stern and prevents water from running down the side of the boat. No black streaks on this girl.
The decks are finished with custom non-skid contrasting surfaces and large waterways carry away any water. Teak decks are provided under the covered aft deck and side decks and also on the centerline of the foredeck where secure footing is so useful in moving to and away from the windlass and anchor gear. The Maxwell anchor windlass is controllable at the bow and at the helm station.
A stainless steel plow and Bruce type anchor are provided. All chain is provided on the primary plow anchor and chain and rode on the secondary anchor. Low profile, heavy duty hatches are provided on the foredeck, above the Office and over the Pilothouse. Custom curved large oval shaped stainless steel handrails provide safety and security and the quality of the welds displays the artistry from the stainless steel shop at NORSEMEN Shipyard, the captive Marlow building yard.
Moving aft, one walks through the centerline gate in the Portuguese bridge, so substantial that it had to be made in two pieces to permit easy handling. There is substantial storage volume for fenders, lines and deck gear in the Portuguese bridge. At the front of the cabin on each side are tank fills for Drinking Water and Fresh Water.
Continuing aft on either side deck, open the hatch in the cabin side and see the tank fill, off the deck so no contaminants can enter. You can fill the tank from either side without needing to drag the fuel hose across the deck. Notice the drip pocket to catch those last few drops that want to fall on your clean deck.
EXTERIOR HARDWARE & FITTINGS
- Twin Maxwell 4000 vertical anchor windlasses
- Anchors 80 pound plow and 100 pound Bruce stainless steel
- Chain anchor rode
- Massive foredeck cleats and hawse pipes
- 4 Fender Holders
- 8 person Life raft
- Life Preservers
- Lower Windshield and Command Bridge windshield covers
- Retractable Heavy Duty Stainless steel and teak swim ladder
- Underwater Lighting
- Aft deck vertical Maxwell 2200 electric docking winches
- Bessenzoni hydraulic extending Passarelle
- Custom CNC cut Nibral “S” class propellers
- Aquamet 22 Shafts, housed inside Velocijet strut keels
- Stainless Steel rudders
Clause de non-responsabilité
Ita Yachts Canada offrent les informations relatives à ce navire de bonne foi mais n’est pas en mesure de garantir l’exactitude de ces informations ni l’état du navire. Il revient à l’acheteur d’instruire ses agents ou ses experts afin de vérifier et de faire valider les informations de son choix. Ce navire est peut-être offert sous réserve, il faut vérifier sa disponibilité. Ce bateau est peut-être offert en partenariat avec un autre courtier.
The Company offers the details of this vessel in good faith but cannot guarantee or warrant the accuracy of this information nor warrant the condition of the vessel. A buyer should instruct his agents, or his surveyors, to investigate such details as the buyer desires validated. This vessel is offered subject to prior sale, price change, or withdrawal without notice. This boat may be listed in partnership with another broker.